beautywrench8

What You Can Do To Get More From Your Key Fob Repairs Near Me

Mon, 26 Feb 2024 03:37:32 +0000

Key Fob Repairs Near Me Key fobs today do much more than just unlock and start the vehicle. They also provide security and are a deterrent to theft. Unfortunately, these advanced devices cost a lot to replace if they malfunction. Finding key car repair who is skilled can be a challenge. Consumer Reports research shows that dealers charge hundreds of dollars to replace a fob. Battery Problems A key fob battery can quickly deplete in the event that it is not replaced in time. This will result in the key fob being unable to communicate with your vehicle anymore and could be an issue if you have a push-to-start engine or would like to use it to unlock doors. It is easy to change the battery on modern key fobs. Firstly, it is important to ensure that you're using the right type of battery for your device (a multimeter can be helpful in this case). The CR2032 battery is the most popular size found in key fobs. However, it is recommended to consult the owner's manual or on the internet to determine the correct battery. After you have purchased the new battery, it's a good idea to test it to determine if the fob will respond correctly. If you notice that you need to click your key fob button several times before it locks or unlocks, this is a clear sign the battery in the fob is not in good condition and needs to be replaced promptly. A damaged battery could cause the keyfob to lose its memory and not respond when a button is pressed, even if it's a new replacement. If you need to hold the key fob nearer to your vehicle to get it unlocked It could be time to replace your keyfob battery. A key fob that's functioning can be used from approximately 20 feet away, but those with dead batteries may only work close to the vehicle. If your key fob isn't working or does not work, it's recommended to contact roadside assistance. A professional can pinpoint the issue to determine if the issue is with the key fob, or the vehicle. The solution can be as simple as replacing the battery in the fob. However, it may be more complicated based on the root cause of the issue. Do not put off fixing your key fob. In the event that you do, you could end up stuck on the side of the highway. Lockout issues Car fobs go through plenty of wear and tear, and they are not indestructible. However, they may be inoperable at the worst possible times, such as when you're pumping gas or putting groceries in your trunk, or heading home after a long workday. The battery is the power source for key fobs. If your key fob's batteries are drained or dead the most popular solution is to replace them. You can usually find the right kind of battery at your local hardware store or an online retailer that sells automotive parts. Some owner's manuals also offer some basic guidelines on how to change the batteries inside the key fob. If replacing the batteries fails to fix the problem it is possible that a professional will be needed to service the fob to reset it for your car. The transmitter of the fob could need to be reset or it may require a new antenna or a software. Some keys may also need a new remote lock solenoid. These are the small devices that are inside each door lock. They send signals to the transmitter on your key fob each time you press the button. A central locking system in newer cars will also send a signal to the transmitter whenever you press one of the buttons on the door lock. A technician can help you diagnose the problem and determine if it's easier to replace the solenoid or transmitter. It's also possible that security features of your vehicle have been reprogrammed in the past since you last changed the batteries on your key fob. This is a very frequent issue in modern vehicles and can be a hassle when it happens. If this is the case, you will need to have a technician reset your key fob and the locks on your vehicle. If you're not able to find a solution, you can try the old-fashioned way of starting your car: press the button on the driver's side. This will start the engine, then turn on the hazard lights and occasionally, the doors will be unlocked. You can also push the unlock button on the key fob. However, this will not allow you to start the engine or open the trunk. Reprograming Issues If you are experiencing problems other than a dead battery, or being locked out of your vehicle, then it may be that your key fob needs to be reprogrammed. If you're unfamiliar with this procedure, you'll need to find a service that is familiar in this field, since doing wrong could result in the key fob not functioning or even causing damage to your vehicle. Most newer cars require a transponder key which is equipped with a tiny radio chip in it. This chip transmits a unique signal when it's inserted into the ignition of your car. This signal is what makes your car recognize keys and open the doors or start the engine. If your car is equipped with transponder keys, it's important to have the chip programmed correctly in order to function properly. When it comes time to reprogram the key fob, it's usually recommended to allow an auto dealer or a shop that specializes in the make and model of your car perform the task. This is because a lot of independent shops don't have the programming equipment for certain newer vehicles. A dealer is the best option if you have an extended warranty or car-insurance policy that covers key-fob related issues. If your key fob isn't working there are a few solutions you can do on your own before asking an expert for assistance. The first step is to replace the batteries. Most fobs come with one battery, and you can purchase a replacement for $10 or less. They are available in many hardware stores and big box retailers, or on the internet. Go through the owner's manual or on the internet to determine what type of battery your key fob needs. One method to fix the issue is to open the fob and look for any signs of damage. These could include cracks on the circuit board, tiny electronic components not fully attached to board, or buttons which are out of place or are loose. YouTube has a variety of videos that will guide you through the procedure. Other Problems Key fobs are electronic devices that allow you to open and start your vehicle at the touch of the button. They may stop working due to a variety of reasons. They work through radio signals or infrared signals. There are many options for replacing or repairing your car key fobs. You can refer to the owner's manual to learn instructions on how you can fix them yourself, or locate an establishment in your area that is specialized in car key fob repair. You can also ask friends and family for recommendations of reliable locksmiths in your neighborhood. A faulty key fob can be caused by a minor problem with the battery. However, other issues could occur that can be more difficult to pinpoint and solve. It's a good idea keep spare batteries in your inventory or keep a spare key fob in case yours fails. The range of a key fob is a different issue. If you find that your vehicle has to be parked right next to the key fob in order to unlock or start it, this can be a sign that the battery is failing. It could also happen when you have to press the button multiple times before your car starts. If changing the batteries does not solve the issue, you can try taking your key fob off to do a visual check. The battery connector terminals can sometimes break, so examining them and carefully soldering them back together can assist in getting your key working properly. You can also try to adjust any buttons that seem to be stuck or broken, though this is usually a task that requires professional attention. In some cases it's simply simpler and less expensive to replace the entire keyfob. This is especially relevant if your car is more recent and features advanced features such as automatic parking. Ask your car manufacturer if the repair is covered under warranty or insurance in the event that you decide to go down this option.

Key Repair Tips From The Top In The Industry

Mon, 26 Feb 2024 02:51:38 +0000

How to Do a Broken Car Key Repair You're in a hurry to get to work and jam your keys into the ignition. You try turning the key however it locks. the lock. There are a few ways you can attempt to resolve the issue before calling a locksmith. Here are a few quick solutions. Super Glue. 1. Contact a locksmith One of the most devastating things that can happen to a car owner is a broken key inside a lock. This is especially frustrating when the driver is in a hurry to get somewhere, or to drop off the child. In this situation it is imperative to act fast to attempt to free the stuck key. A locksmith with experience is the best option as they will have the proper tools and know how to get rid of the keys broken without damaging the lock. Many people will look for something that is thin and rigid such as paperclips or toothpicks. But this isn't the best solution as they are too heavy to fit inside the lock. The best option is to use a pair tweezers. They are lightweight and can easily reach into the lock. They should be able to grasp the damaged part of a key, and then pull it out. If you don't own tweezers, it might be worth looking for a set available at auto parts stores. These are flat, narrow and have small hooks. They can be put into the keyhole and then grasp the broken piece of the key. Another option is to find a magnetic key hook that can stick to the metal inside the lock and pull it out. This is not always a good idea since it is possible for it to get caught under the lock and cause further damage to it. In such a situation, it is best to call an expert locksmith. Some people try to glue together the two pieces of a damaged car key using superglue in order to remove it from the lock. However, this is extremely risky since the pieces of metal may cling to each other and then break apart later. It is also crucial not to turn the key as this can cause further damage to the lock or ignition cylinder. It is recommended to contact a professional locksmith who will be ready to remove the damaged key and then make an immediate replacement. 2. Drill a hole Sometimes a key breaks inside the lock, and even if you have an extra key, you may not be in a position to gain access to your vehicle. In these cases drilling the lock is the best option. First, you need to make sure that the key hole is designed to accept a basic tumbler car key. If it isn't then you won't be able to drill out the pins without damaging the door and possibly damaging the lock mechanism. It is important to note that you will drill through the outer layer of plastic as well as an inner layer of metal. You can drill through these layers using a the smallest drill bit but you shouldn't go any further. Drilling too deep can cause damage to the wiring harness or cause the drill to snag. It is also recommended to wear a mask and protective gear while working with drilling. This will stop dust and dirt from getting into your lung. It's also a good idea, if the broken key piece is sticking out of the lock, to keep a pair pliers and tweezers in your bag. If the key is protruding enough to be able to be grasped with pliers and tweezers, this is enough to pull it out. If not, however you'll need to use tools like this one to insert the tool in the lock, and then turn it toward the key to grasp it and remove it from the hole. 3. Drill a nail You may be left in limbo in the event that you break your key in half. There are a number of options to fix the problem without the expense of an locksmith. The first option is to utilize a screw or nail. These can be found in your home or at a local hardware store. It is recommended to search for the nail that is as thin and as long as you can. This will allow you to fit it in the hole and then use epoxy to link the two parts together. Make sure that the back of the nails is flat. This will allow it to fit into the slot cut in the key. This will stop it from moving around and potentially breaking again in the future. 4. Super Glue Many car owners tend to make use of DIY techniques like using super glue attempt to fix a damaged car key, but this is a dangerous thing to do. You could end up damaging the lock and be forced to shell out more money to replace it. The first step is to take a look at the keys that have been damaged and ensure that they match each other in terms of size. This is crucial to ensure that all the pieces that have been glued are aligned correctly and that the key will fit in the lock after they've been joined. Then, using a piece of fine-grit paper or a metal filing, smooth out the edges of the broken pieces. This will help make the glue stick better and reduce the chances of a key becoming loose in the future. After polishing the edges After polishing the edges, apply a small amount (about an amount of pea-sized) of super glue on the other side. Only apply key fob repairs of super glue, since excessive amounts can make the key too large. It will then be difficult to fit into the lock. After lining up the two pieces of the broken key then press them together. After several seconds the glue will begin to set and bond the key fragments together. Another household item that can be used to help extract a broken car key is a paperclip or bobby pin that can be made into a pick-like tool and put into the lock. This method is particularly useful when the damage is close to or within the keyway or lock hole. A car key that has been damaged with electronic components will require an entirely new key from the locksmith or dealer. This is because the key needs to be programmed with a brand new code and the chip will need to be replaced. If the shell or metal part of the key fails, you will need to have a new cut. You don't have to reprogramme or replace the electronics.

10 Undeniable Reasons People Hate Key Fob Repair

Mon, 26 Feb 2024 02:47:05 +0000

Key Fob Repair: Replacing the Battery The buttons on key fobs can become damaged and stop functioning properly after being tossed around in pockets and purses. Replacing the small battery, which a majority of car fobs have in a snap-out case, may fix the issue. If the contacts inside the key fob are damaged, a new replacement may not be enough to bring it back to life. This is a simple fix that you can do at home. Replace the Battery If your key fob is feeling sluggish or takes a longer time to unlock or lock your car, it may be time to replace the battery. The replacement of a key fob's battery is among those easy tasks you can complete yourself. It's also a cost-effective fix that could save you a trip to an expert locksmith or dealer. You can buy coins-style (CR2032) battery at any auto parts or home improvement general retailer. Key fobs come with a slot for these batteries and it is simple to replace the battery. Depending on the manufacturer you might need make use of a screwdriver to open the compartment. If your key fob has clips that hold the batteries in place, remove them with your fingers or other non-metallic tools. Install the new battery, taking care to install it correctly. Note its orientation when removing the old one. Avoid touching the flat surfaces of the batteries as they can cause damage to their lives. Once the new battery is installed then close the key fob's case and test it by pressing the button to ensure it works. If the key fob isn't working, you might have to reopen it and verify that the battery is inserted correctly. You may also find that simply replacing the battery isn't enough to solve the issue. key fob repairs could be caused by physical or electrical trauma. In this instance, you will need to take your key fob to a dealership or auto service center for repairs. Before you do this, there are four issues that a replacement battery cannot solve. It is important to be aware of these problems so that you're able to seek out an expert technician in the event of need. You can also find out how to fix the faulty transmitter of a key fob to find out why it is not working. Clean the Contacts Maintaining your key fob's cleanliness is essential to its function and life. Over time, natural oils from your hands and pockets can accumulate on the key fob's buttons and crevices and even cause keys to cease working completely. It's easy enough to fix – all you need is some cleaning alcohol and a cotton swab. First, open up the key fob by taking the lid off with a screwdriver or coin and gently prying out the battery. Be sure to note the type of battery it is (negative and positive sides) so that you can insert it again correctly after you're done. Then, moisten a cotton swab or small brush with isopropyl (rubbing) alcohol and begin taking off the dirt from all buttons on the fob and the surrounding areas. Pay special attention to the battery's contacts, making sure that they are clean of grease or dirt. Once you are done, be sure to let the fob as well as its components dry completely. If your fob still won't function after cleaning it, it may be an idea to reset the system. Check the owner's manual to find out how to reset the system. This could be able to bring the key fob back to normal if the issue was due to the battery being dead. It is important to maintain the key fob regularly after it is cleaned and resynchronized. By regularly wiping it down with a damp cloth and mild soap, you can be sure that your key fob will function well for many long time to come. Reset the system Despite the fact that today's high-tech keys fobs are more efficient, secure, and convenient than ever before, it's possible that they encounter some problems. Fortunately, most times the issues aren't major or complex, and can be fixed with simple methods like replacing the battery. If the problem is more severe or the issue can't be solved using simple methods such as a professional auto repair shop can repair and replace the key fob. Getting your car to lock or unlock with the key fob is the principal function of the device, however, it can also be used to enable certain vehicle features. The key fob can be used to lower or lift a sunroof. This feature is very useful when you're stuck in traffic and need to open your roof. The key fob is also helpful in bringing your car to life when it's parked in an awkward location. The internal circuitry inside the key fob may fail due to defects in manufacturing or wear and tear. It could be a sign of erratic behavior or total failure to lock or unlock the car. Moisture or other electromagnetic interference sources may sometimes affect the function of a keyfob. If your key fob has become dirty or wet, or is contaminated by dust, it's going to require cleaning prior to being used again. Replacing the battery on the key fob or cleaning the contacts might help fix a malfunctioning device however, if it continues to run erratically you might need to perform a factory reset. This will help eliminate bugs in the system and restore the operation of the device. If you're not sure how to reset your device then consult the device's owner's guide or the manufacturer's site. Certain models require a specific tool to complete the reset however, you should be able to locate instructions that are applicable to the specific model you have. Another option to resolve issues with your key fob is to contact an Apache Junction mobile car locksmith. They are able to replace and program key fobs on almost all models of automobiles. They can also fix keys with chips.

Avoid Making This Fatal Mistake You're Using Your Automotive Key Repair

Mon, 26 Feb 2024 02:43:40 +0000

Automotive Key Repair – What to Do When Your Car Key Won't Turn in the Ignition We've all been there: your car key refuses to engage the ignition. It could happen at the worst possible time, such as when you're filling your car with groceries or heading home from work. Rather than panic instead, there are a variety of solutions to get you back on the road. Here are a few common key issues in the automotive industry and solutions: Broken or bent keys The most frequent reason a car owner cannot begin their vehicle is a bent key. This can be easily repaired by simply straightening the key. This may sound simple but it's important to do it with care. The key is very thin and may break if bent even a little. To do this, you'll need an area that is stable, as well as a pair of pliers. Take one end of the key using the pliers and bend it until it is straight. It is best to do this on the floor or in a vice. Then, you can put it into the lock to see if it turns. If not, it may be time to have a new key cut. This will save you from having to call a locksmith and will ensure that your key works. Keep a spare key in your purse so you're not without access to your vehicle if it is damaged. If you are experiencing issues with a bent or broken key, try putting some lubrication on it before inserting it into the lock. This will make it easier to move through the cylinder and will prevent it from getting stuck. You can use graphite or spray lubricant. Make use of the plastic tube that comes with the spray for a more precise application. This will also help keep moisture from damaging your key. Spring pins and springs with pins Sometimes a pin (also called a roll pin) or spring may become stuck. A pin is a small 2 to 3 inches (5.1-7.6 cm) long piece of metal with hollow ends used to connect two parts of an equipment. In the majority of instances, it is possible to remove a pin by simply pulling it out with your fingers or a wrench. If you own an older vehicle that has a microchip key it is likely that the key will need to be programmed in order to function with your car. This process can vary depending on the manufacturer and car. Contact us for assistance with your vehicle keys or locks! We can repair or replace every key for your vehicle. Selector for gears It's crucial to take your car to a mechanic as quickly as you can when the gear selector is stuck in park. It's a safety issue and could cause serious damage to your vehicle if continue to drive it. This could also be a sign that the transmission is experiencing more serious problems that are expensive to repair. Most times, this problem is easily fixable. Most often, the cable end that is attached to the lever could snap or become disconnected. The mechanic can repair this issue in a matter of minutes. In certain instances, the bushings of the gear selector may be damaged or worn. These are rubber covers that go around joints within the gear system to help it move more smoothly. They perform the same function to cartilage in your knees therefore it is important to ensure that they stay in good shape and soft. You can extend the life of your gear selector by doing a few easy things. It is best to avoid the gear selection in very cold temperatures. This is because the cables that control the gear are prone to freezing and cracking. It is also recommended to replace your bushings, for instance those made by First Line, with high-quality ones. These bushings are an essential part of your gear selector, and shouldn't be overlooked. If you find that yours is worn out, you should visit an auto repair shop specializing in Land Rover repairs. They will help you find the right parts to fix the gear selection system. They can also provide many other services, like maintenance and repair of your transmission. Dead battery If you turn the ignition on and hear only a click, then your battery is dead. As batteries age, they go through natural processes that cause them to die prematurely. The negative plates of your car battery will start to become coated with sulfate crystals. A dead battery may cause you to lose electrical power within your vehicle, causing the radio or electric windows to stop working. If your car is having issues getting started in cold weather, this is a good sign that it's time for an upgrade to your battery. It is possible that your problem is not a dead battery but an issue with the charging system. This issue can be solved by having your mechanic verify that the alternator, serpentine belt, and battery cables all work properly. A key fob that is not functioning properly is another common problem for automotive key repair. The key fob is connected to the computer in your car and relays signals as well as commands between the engine and accessory systems. The system may become confused or stop communicating with your car if it is exposed to extreme temperatures or is wet. It is usually possible to reset the lost key fob following the steps in the owner's guide. Depending on the type of vehicle it could involve opening and closing the doors, turning lights and other electronics on and off or pressing a certain sequence of buttons. If this doesn't fix your fob, it could require professional programming, which will require an expert technician. But it's still worth attempting these steps before you decide to shell out for a new one. Ignition socket Modern car keys come with a transponder, which when it is inserted into the ignition, transmits the signal. repair car key informs the immobilizer on the car if it is the right one to allow it to start. In the 1990s, car theft became a major issue. The majority of manufacturers have installed this transponder system for security and insurance reasons. If you own a newer car, the only way to replace your keys could be through the dealership or by contacting the manufacturer directly. Before you visit note down the VIN number of your vehicle (vehicle identification number). This number is usually found on the dashboard's front, door jamb, or in your owner's manual. Bring your current key to an AutoZone participating store. A representative will use a machine that will trace the contours of the blank key in order to precisely replicate the original key. The new key will be cut on-site using a precision cutting machine. If your key is blade style or key fob or has a thick black or grey head, it'll need to be programmed to the specific car you own before it can be used to start the engine.

7 Things You've Always Don't Know About Key Repair

Mon, 26 Feb 2024 02:42:52 +0000

How to Fix a Key Scratch on Your Car There are many options to consider when you've got a scratch on the key of your car and would like it repaired. Mobile auto detailing experts can fix the scratch and restore the original appearance of your car. Begin by noting and identifying the issue with the key. Then test the key to ensure it's working correctly. 1. Remove the cap on the key. Because of their constant use, keyboards are susceptible to wear and tear. They also tend to collect hair, dust, and food which can cause them to malfunction. Cleaning your keyboard will help get rid of these particles and extend the life of your Keyboard. First, shut off your computer and disconnect the keyboard if it is possible. This will prevent you from accidentally typing commands while working on the keyboard. Find a clear area in which you can place all the keys. This will help you reconnect them after you've finished. If you don't have a keycap remover tool, you could try using an flathead screwdriver or butter knife. You can also try making a paperclip into an “U” shape and bending the ends to hook under a key. Once you've removed the keycap clean it off and wipe the switch clean. You can also clean the stems of keys that are the tiny towers or clips that extend from the faceplate of each key. Use car key fob repair near me that has been dipped in isopropyl alcohol to wipe off any debris on the faceplate. Be careful not to spill any alcohol on the printed parts of the key, as it may cause damage to the key. Reattach the key after washing it. Begin with the upper left corner and proceed to each row one key at one time. If you're using a brand new keycap, it's best to align it with the keyswitch and press down evenly across the sides to snap it into place. When you're reconnecting the keycap pay attention to larger keys, such as the enter and space bar. These keys are connected to a metal support bar which can easily be damaged when you're not cautious. After you've put all of the keycaps on the keyboard, press down on the keys to test them. When the keycap is properly reattached, you should hear a click sound and feel it pressing down. If you do not, you may have to try reattaching it or consult a professional. 2. Clean is the most important thing. A key can feel sticky and mushy for various reasons, but the most common is that it's not properly set in its base or the key mechanism. The most effective way to fix this problem is to employ a flathead screwdriver, or butter knife to pry the corner of the key free. The key will be removed in a snap. You can clean it by washing it in water or alcohol. If your keys are rusty and are dirty, you can clean them using salt and lemon. You can also soak them in a mixture of water and vinegar. Shut down your computer and unplug it if necessary. It is also essential to keep yourself grounded, as the final thing you want is to damage delicate electronic components by static electricity. Begin by wiping the keys and their surroundings using a lint free cloth. Make sure you wring it out thoroughly to ensure there is no moisture between the keys. Make sure you use a gentle cleaning solution because stronger cleaners could damage the plastic. Use a cotton swab that has been dipped in isopropyl (rubbing) alcohol to clean the edges of the key. Be careful not to get any of the alcohol on the printed area as this could cause discoloration or even strip the letters off your keys. You can also get an electronic cleaning brush available at a general store to help remove hard-to-clean dirt and debris. You can also buy products in a gel consistency that can be applied to your keyboard and then peeled away. This will remove any loose debris that has accumulated between your keys. If you've tried all the above options but your key still feels soft or sticky, it could be time to replace it. This could be a simple or complex process, depending on the kind of keys. It is possible to disassemble the entire key mechanism to take out the old one and replace it with a new one. 3. Reattach the keycap We don't think about our keys until they are damaged or locked in the car. It can be a real problem, but it's possible to fix it and save money. Try using compressed air to remove any dust or debris that could be blocking the switch. If this isn't working, try prying the key cap off and clean it. Use a plastic prying tool, like credit-cards or a Spudger. (You could also make use of a knife if are in rush). Also, you should carry a small tool, such as a toothpick or tweezers for cleaning the tiny grooves in the key. After you've cleaned the key, you can put it back on the keycap and test it. If the key does not respond, you may have to replace your key switch. If your keyboard is worn out or the switch on your keyboard is damaged, you'll have to purchase a replacement and then attach it. This is a more complicated fix, but it's usually the only option if the key is no longer working. One of the most common reasons for the key to stop working is due to the accumulation of dust under the key. If this is the situation, all you have to do is clean the area thoroughly and get rid of any dirt or other debris. Another reason that can cause a key to stop functioning is because the switch on the key has corrosion-prone. This can happen if water or any other liquid gets into the switch, and this can cause corrosion that will eventually eat away at the pins of the key switch and connectors on the circuit board. You can avoid this by cleaning the circuit board prior to replacing the key. This will help to make the switch more resistant to corrosion, and it will also make it easier to pop out and then solder into a new key switch. If you're not confident fixing the laptop yourself and you don't feel confident, take it to an electronics repair shop. They will be able inform you if your key switch is repairable and if not, they can replace it. 4. Test the key If a key isn't able to start the car, it could be frustrating and even dangerous. It can also be expensive if you need to buy a replacement key fob. Before you head to the electronics or auto store, you can try a few quick solutions. Try first a spare key in order to determine if it's the original key that is causing the issue. This will help you narrow down the problem and save you money in the end. If the key doesn't work, you need to disassemble it to determine what the problem is. The majority of keys are made up of three components that are the key cap as well as the key carriage and the key pad. Each of these parts can cause a variety of issues for the key. The key cap can be loose or tilted. This can stop the key from snapping into position when you press the key. You can usually fix this by re-seating the key cap. Another possibility is that the key pad or the key pad could be damaged or dirty. These parts are hard to fix, but they can be cleaned with the use of a toothpick and a tweezer. You should be careful not to harm any internal parts as this could cause the key to stop working completely. You can also try performing an experiment with a rollover test. This test checks whether the key is able to register more than one key combination at the same time. It is possible to test this by pressing multiple keys at the same time and then determining whether or not they all register correctly. If any of the keys fail to register, they might require cleaning or replaced. You can also replace the battery on your key fob. This is a quick and cheap method of testing your key and also allow you to determine if the problem is caused by the battery being dead or a malfunctioning ignition switch.